Nov 7, 2025

Reinspection (002)

11 minor violations. 1 corrected on site.

View 11 violations

Applicability of article; compliance; penalty for violation; variances, etc. operating a food service / processing establishment not conforming to requirements of article ii.

20-19(b)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

20-21.03(b)(10)b

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

20-21.11(a)(08)c[04]

Single-service articles. single-service and single-use articles not stored at least six inches (15 cm) above the floor on dollies / pallets / racks / skids designed as specified under section 20-21.03(a)2b of this code / not kept in closed cartons that protect them from contamination, except for automatic fire protection sprinkler heads that may be required by law. (corrected on site)

20-21.14(c)(01)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

Hand-washing sink maintenance. hand-washing sink / soap dispenser / hand-drying device/ related fixtures not kept clean / not in good repair.

20-21.19(d)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be maintained in good repair.

20-21.22(a)

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

20-21.22(f)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

20-21.23(a)

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

20-21.23(g)

Special ventilation. filters not cleaned at sufficient frequency to prevent accumulation.

20-21.25(b)(03)

58

Nov 5, 2025

Reinspection (002)

18 minor violations.

View 18 violations

Applicability of article; compliance; penalty for violation; variances, etc. operating a food service / processing establishment not conforming to requirements of article ii.

20-19(b)

General. raw / prepared food removed from original containers / packages being stored in unclean containers / being stored in uncovered containers..

20-21.03(a)(01)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

20-21.03(b)(10)b

Dispensing utensils not stored with the handle extended out from the food.

20-21.05(f)(01)

Materials; general. multi-use equipment and utensils not designed, constructed and repaired with safe materials, including finishing materials / not corrosion-resistant and nonabsorbent / not smooth, easily cleanable and durable under conditions of normal use.

20-21.10(a)

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

20-21.10(m)

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

20-21.11(a)(07)

Using chemicals for sanitization. when using chemicals for sanitization, a test kit or other device that accurately measures the concentration of the solution in parts per million or milligrams per liter not provided and used.

20-21.12(g)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

Hand-washing sink maintenance. hand-washing sink / soap dispenser / hand-drying device/ related fixtures not kept clean / not in good repair.

20-21.19(d)

Controlling pests, generally. effective measures intended to eliminate the presence of rodents, flies, cockroaches, and other insects on the premises not utilized.

20-21.21(a)

Removing dead or trapped birds / insects / rodents / other pests. dead or trapped birds / insects / rodents / other pests not removed from control devices and the premises at a frequency that prevents the accumulation or attraction of pests and minimizes exposure to decomposing remains.

20-21.21(d)

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

20-21.21(b)

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

20-21.22(f)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be maintained in good repair.

20-21.22(a)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

20-21.23(a)

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

20-21.23(g)

General. equipment / utensils not in current use not stored in a clean and sanitary condition.

20-21.28(a)(03)

41

Nov 4, 2025

Reinspection (002)

18 minor violations. 1 corrected on site.

View 18 violations

General. the internal temperature of time/temperature controlled for safety (tcs) food not maintained at 41°f (05°c) or below or 135°f (57°c) or above at all times, except as otherwise provided in this article or unless a packaged product is so labeled as exempted and approved by the appropriate state or federal health authority. (corrected on site)

20-21.02(a)(01)

General. container of food not stored a minimum of 6 inches above the floor.

20-21.03(a)(02)

General. raw / prepared food removed from original containers / packages being stored in unclean containers / being stored in uncovered containers..

20-21.03(a)(01)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

20-21.03(b)(10)b

Materials; general. all equipment and utensils not maintained in good repair.

20-21.10(a)

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

20-21.10(m)

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

20-21.11(a)(07)

Single-service articles. single-service and single-use articles not stored at least six inches (15 cm) above the floor on dollies / pallets / racks / skids designed as specified under section 20-21.03(a)2b of this code / not kept in closed cartons that protect them from contamination, except for automatic fire protection sprinkler heads that may be required by law.

20-21.14(c)(01)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

General. plumbing not sized / installed / maintained according to applicable laws.

20-21.17(a)

Toilet room. toilet facility / vestibule, not kept clean / not in good repair / not free of objectionable odors.

20-21.18(c)

Hand-washing sink supplies. hand-washing sink or group of adjacent hand-washing sinks not provided with individual, disposable towels / a continuous towel system that supplies the user with a clean towel / a hand-drying device providing heated air or a hand-drying device that employs an air-knife system that delivers high velocity, pressurized air at ambient temperatures.

20-21.19(c)

Controlling pests, generally. premises not kept in such condition as to prevent the harborage or feeding of insects or rodents.

20-21.21(a)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be kept clean.

20-21.22(a)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

20-21.23(a)

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

20-21.23(g)

Protective shielding. light bulbs not shielded / coated / otherwise shatter-resistant in areas where there is exposed food, clean equipment / utensils / linens / unwrapped single-service or single-use articles, except as specified in subitems a and b of this item shielded / coated / otherwise shatter-resistant bulbs need not be provided in areas used only for storing food and single-service articles in unopened packages if the integrity of the packages cannot be affected by broken glass falling onto them and the packages are capable of being cleaned of debris from broken bulbs before the packages are opened.

20-21.24(b)(01)

General. food establishment and all parts of the property used in connection with operations of the establishment not kept free of litter and items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer in use.

20-21.28(a)(01)

41

Jul 1, 2025

Reinspection (002)

24 minor violations. 6 corrected on site.

View 24 violations

General. bulk food removed from original container not stored in a container identifying the food by common name.

20-21.03(a)(06)

General. food not in sound condition / safe for human consumption / free from spoilage, filth, other contaminants. food prepared in or obtained from an unlicensed private home or other unlicensed food establishment is considered to be from an unapproved source and may not be used or offered for sale for human consumption in or from a food establishment. (corrected on site)

20-21.01(a)

Hot storage. time/temperature controlled for safety (tcs) food in hot storage not being held at 135°f (57°c) or above. (corrected on site)

20-21.03(c)(02)

Refrigerated storage. cold storage of foods. time/temperature controlled for safety (tcs) food not maintained at 41°f (5°c) in cold storage. (corrected on site)

20-21.03(b)(09)

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

20-21.10(m)

Materials; general. single-service and single-use articles. single-service articles / single-use articles reused. (corrected on site)

20-21.10(a)(05)

Materials; general. all equipment and utensils not maintained in good repair.

20-21.10(a)

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

20-21.11(a)(07)

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

20-21.11(a)(08)c[04]

Cleaning frequency. equipment, food-contact surfaces, and utensils not clean to sight and touch.

20-21.11(a)(13)

Storage. utensils and equipment not air-dried before being stored / not stored in a self-draining position. utensils and equipment may not be cloth-dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry. (corrected on site)

20-21.14(b)(02)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

General. plumbing not sized / installed / maintained according to applicable laws.

20-21.17(a)

Hand-washing sink supplies. when disposable towels are used, easily cleanable waste receptacles not conveniently located near the hand-washing facilities. (corrected on site)

20-21.19(c)

Hand-washing sink faucets. hand-washing sink not equipped to provide water at a temperature of at least 100°f (38°c) through a mixing valve or combination faucet. hand-washing sinks in facilities providing custodial care for preschool age children that are used only by the children may provide only cold running water.

20-21.19(b)

Removing dead or trapped birds / insects / rodents / other pests. dead or trapped birds / insects / rodents / other pests not removed from control devices and the premises at a frequency that prevents the accumulation or attraction of pests and minimizes exposure to decomposing remains.

20-21.21(d)

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

20-21.21(b)

Controlling pests, generally. effective measures intended to eliminate the presence of rodents, flies, cockroaches, and other insects on the premises not utilized.

20-21.21(a)

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

20-21.22(f)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be kept clean.

20-21.22(a)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

20-21.23(a)

Protective shielding. light bulbs not shielded / coated / otherwise shatter-resistant in areas where there is exposed food, clean equipment / utensils / linens / unwrapped single-service or single-use articles, except as specified in subitems a and b of this item shielded / coated / otherwise shatter-resistant bulbs need not be provided in areas used only for storing food and single-service articles in unopened packages if the integrity of the packages cannot be affected by broken glass falling onto them and the packages are capable of being cleaned of debris from broken bulbs before the packages are opened.

20-21.24(b)(01)

Cleaning equipment storage. after use, mops not placed in a position that allows them to air-dry without soiling walls / equipment / supplies.

20-21.28(e)

General. food establishment and all parts of the property used in connection with operations of the establishment not kept free of litter and items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer in use.

20-21.28(a)(01)

30

May 15, 2025

Complaint (003)

27 minor violations. 9 corrected on site.

View 27 violations

8-304.11(k) the permit holder shall notify customers that a copy of the most recent establishment inspection report is available upon request by posting a sign or placard in a location in the food establishment that is conspicuous to customers or by another method acceptable to the regulatory authority. (corrected on site)

20-20(c)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”. (corrected on site)

20-21.03(b)(10)b

Refrigerated storage. cold storage of foods. time/temperature controlled for safety (tcs) food not maintained at 41°f (5°c) in cold storage. (corrected on site)

20-21.03(b)(09)

Refrigerated storage. methods for rapid cooling. approved methods for rapid cooling not utilized. (corrected on site)

20-21.03(b)(03)

General. raw / prepared food removed from original containers / packages being stored in unclean containers / being stored in uncovered containers.. (corrected on site)

20-21.03(a)(01)

General. bulk food removed from original container not stored in a container identifying the food by common name.

20-21.03(a)(06)

Cooking time/temperature controlled for safety (tcs) foods. permit holder failed to inform consumers of the significantly increased risk of consuming foods by way of a disclosure and reminder, as specified in items (06) and (07) of this subsection by using brochures / deli case or menu advisories / label statements / table tents / placards / other effective written means when animal food such as beef / eggs / fish / lamb / milk / pork / poultry / shellfish is served or sold raw / undercooked / without otherwise being processed to eliminate pathogens either in ready to eat form or as an ingredient in another ready to eat food (except as specified in items (03) and (08) of this subsection).

20-21.04(c)(05)

Dispensing utensils. no suitable dispensing utensils provided for employees / consumers during pauses in food preparation / dispensing. (corrected on site)

20-21.05(f)

Materials; general. all equipment and utensils not maintained in good repair.

20-21.10(a)

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

20-21.11(a)(07)

Single-service articles. single-service and single-use articles not stored at least six inches (15 cm) above the floor on dollies / pallets / racks / skids designed as specified under section 20-21.03(a)2b of this code / not kept in closed cartons that protect them from contamination, except for automatic fire protection sprinkler heads that may be required by law. (corrected on site)

20-21.14(c)(01)

General. plumbing not sized / installed / maintained according to applicable laws.

20-21.17(a)

Toilet fixtures. toilet room not provided with at least one covered waste receptacle.

20-21.18(d)

Hand-washing sink installation. hand-washing sink used for purpose other than hand-washing as specified in section 20-21.08(b) of this code. (corrected on site)

20-21.19(a)

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

20-21.20(a)(03)

Containers. garbage / recyclables / returnables / refuse not kept in durable / easily cleanable / insect-proof and rodent-proof containers that do not leak and do not absorb liquids. plastic bags and wet-strength paper bags may be used to line the containers, and they may be used for storage inside the food establishment.

20-21.20(a)(01)

Maintaining refuse areas and enclosures. storage area / enclosure for refuse / recyclables / returnables not maintained free of items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer used, as specified in section 20-21.28(a)(03) / not maintained clean.

20-21.20(h)

Openings. openings to the outside not effectively protected against the entrance of rodents.

20-21.21(b)

Controlling pests, generally. effective measures intended to eliminate the presence of rodents, flies, cockroaches, and other insects on the premises not utilized.

20-21.21(a)

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

20-21.22(f)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be kept clean.

20-21.22(a)

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

20-21.23(g)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not kept clean.

20-21.23(a)

Special ventilation. filters not cleaned at sufficient frequency to prevent accumulation.

20-21.25(b)(03)

Labeling of materials. working containers used for storing poisonous / toxic materials such as cleaners and sanitizers taken from bulk supplies not clearly / individually identified with the common name of the material. (corrected on site)

20-21.27(b)

General. food establishment and all parts of the property used in connection with operations of the establishment not kept free of litter and items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer in use.

20-21.28(a)(01)

Food establishment failed to maintain on premises a certificate of completion of the food handler course for each food employee.

20-53(g)

26

Feb 4, 2025

Complaint (003)

No violations found.

100

Jan 6, 2025

Routine Inspection (001)

7 minor violations. 2 corrected on site.

View 7 violations

8-304.11(k) the permit holder shall notify customers that a copy of the most recent establishment inspection report is available upon request by posting a sign or placard in a location in the food establishment that is conspicuous to customers or by another method acceptable to the regulatory authority.

20-20(c)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”. (corrected on site)

20-21.03(b)(10)b

Hand-washing sink supplies. supply of hand-cleansing liquid / powder / bar soap not available at each hand-washing sink or group of two adjacent hand-washing sinks. (corrected on site)

20-21.19(c)

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

20-21.20(a)(03)

Attachments. decorative materials in other than consumer areas attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

20-21.23(g)

General. food establishment and all parts of the property used in connection with operations of the establishment not kept free of litter and items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer in use.

20-21.28(a)(01)

Food establishment failed to maintain on premises a certificate of completion of the food handler course for each food employee.

20-53(g)

70

Jan 17, 2024

Complaint (003)

6 minor violations.

View 6 violations

Manual sanitizing. food-contact surfaces of all equipment and utensils not sanitized by immersion in a chlorine solution in a manner that complies with one of the following; 25 ppm at a minimum temperature of 120of for 10 seconds when ph is <=10, 50 ppm at a minimum temperature of 100of for 7 seconds when ph is <=10, 50 ppm at a minimum temperature of 75of for 7 seconds when ph is <=8, or 100 ppm at a minimum temperature of 55of for 10 seconds when ph is <=10.

20-21.12(e)(02)

Single-service articles. single-service and single-use articles not stored at least six inches (15 cm) above the floor on dollies / pallets / racks / skids designed as specified under section 20-21.03(a)2b of this code / not kept in closed cartons that protect them from contamination, except for automatic fire protection sprinkler heads that may be required by law.

20-21.14(c)(01)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

Hand-washing sink supplies. when disposable towels are used, easily cleanable waste receptacles not conveniently located near the hand-washing facilities.

20-21.19(c)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be maintained in good repair.

20-21.22(a)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not kept clean.

20-21.23(a)

74

Dec 7, 2023

Routine

No violations found.

100

Dec 5, 2023

Complaint (003)

13 minor violations. 1 corrected on site.

View 13 violations

Applicability of article; compliance; penalty for violation; variances, etc. permit holder / person in charge of the food establishment / mobile food unit not in compliance in accordance with provisions of article ii concerning food storage / food preparation / food display / training of employees in basic food safety principles including allergy awareness / not ensuring that food and conditional employees are informed of their responsibility to report information regarding health and activities as they relate to diseases that are transmissible through food / not ensuring written procedures and plans are developed by the food establishment are maintained / implemented.

20-19(d)

General. bulk food removed from original container not stored in a container identifying the food by common name.

20-21.03(a)(06)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

20-21.03(b)(10)b

Cooking time/temperature controlled for safety (tcs) foods. permit holder failed to inform consumers of the significantly increased risk of consuming foods by way of a disclosure and reminder, as specified in items (06) and (07) of this subsection by using brochures / deli case or menu advisories / label statements / table tents / placards / other effective written means when animal food such as beef / eggs / fish / lamb / milk / pork / poultry / shellfish is served or sold raw / undercooked / without otherwise being processed to eliminate pathogens either in ready to eat form or as an ingredient in another ready to eat food (except as specified in items (03) and (08) of this subsection). (corrected on site)

20-21.04(c)(05)

General. contamination event. food establishment without written procedures for employees to follow when responding to vomiting or diarrheal events.

20-21.07(a)(03)

Materials; general. all equipment and utensils not maintained in good repair.

20-21.10(a)

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

20-21.11(a)(07)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

20-21.17(c)

Floor junctures. when allowed in this subsection, the juncture between walls and floors presenting an open seam of more than one-thirty-second of an inch.

20-21.22(f)

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be kept clean.

20-21.22(a)

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not kept clean.

20-21.23(a)

Special ventilation. filters not cleaned at sufficient frequency to prevent accumulation.

20-21.25(b)(03)

Food employee failed to successfully complete a food handler training course within 60 days of employment.

20-53(f)

52

Chacho's #6