Goode Eats Southern Cuisine

8-304.11(k) the permit holder shall notify customers that a copy of the most recent establishment inspection report is available upon request by posting a sign or placard in a location in the food establishment that is conspicuous to customers or by another method acceptable to the regulatory authority.

Special requirements. manufactured food. all food manufactured, processed, or packaged in commercial food processing establishments or commissaries not labeled according to all applicable laws as defined in tfer 228.78 and 228.79.

General. bulk food removed from original container not stored in a container identifying the food by common name.

Materials; general. multi-use equipment and utensils not designed, constructed and repaired with safe materials, including finishing materials / not corrosion-resistant and nonabsorbent / not smooth, easily cleanable and durable under conditions of normal use.

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

Floors. floors and floor coverings of all food preparation, food storage, utensil-washing areas, walk-in refrigerating units, dressing rooms, locker rooms, and toilet rooms shall be nonabsorbent.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

Construction. walls, including nonsupporting partitions / wall coverings / ceilings, of walk-in refrigerating units / food preparation areas / food storage areas / food display areas / equipment-washing areas / utensil-washing areas not light-colored / smooth / nonabsorbent / easily cleanable except for ceilings over areas used only for beverage preparation and/or service. concrete or pumice blocks used for interior wall construction in these locations shall be finished and sealed to provide an easily cleanable surface except in dry storage areas. (corrected on site)

Signs clearly stating that smoking is prohibited within not conspicuously posted at every entrance to a public place.

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”. (corrected on site)

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

Containers. in containers designed with drains, drain plugs not in place at all times, except during cleaning.

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means. (corrected on site)