Runners Chevron

Refrigerated storage. refrigeration facilities. each mechanically refrigerated facility storing time/temperature controlled for safety (tcs) food shall be provided with numerically scaled indicating thermometer, accurate to 3°f if scaled in fahrenheit only. . recording thermometers, accurate to 3°f if scaled in fahrenheit only, may be used in lieu of indicating thermometers. thermometers that are scaled in celsius or dually scaled in celsius and fahrenheit shall be designed to be easily readable and accurate to ±(1.05°c) in the intended range of use.

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

General. bulk food removed from original container not stored in a container identifying the food by common name.

Materials; general. multi-use equipment and utensils not designed, constructed and repaired with safe materials, including finishing materials / not corrosion-resistant and nonabsorbent / not smooth, easily cleanable and durable under conditions of normal use.

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. food-contact surfaces of grills, griddles, and similar cooking devices and the cavities and door seals of microwave ovens not cleaned at least once a day; except that this shall not apply to hot oil cooking and hot oil filtering equipment if it is cleaned as specified in subsection (f) of this section. the food-contact surfaces of all cooking equipment shall be kept free of crusted grease deposits and other accumulated soil.

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris. (corrected on site)

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

General. food not in sound condition / safe for human consumption / free from spoilage, filth, other contaminants. food prepared in or obtained from an unlicensed private home or other unlicensed food establishment is considered to be from an unapproved source and may not be used or offered for sale for human consumption in or from a food establishment. (corrected on site)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) and ready to eat food stored at 41°f (5°c) for more than seven days. (corrected on site)

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. food-contact surfaces of grills, griddles, and similar cooking devices and the cavities and door seals of microwave ovens not cleaned at least once a day; except that this shall not apply to hot oil cooking and hot oil filtering equipment if it is cleaned as specified in subsection (f) of this section. the food-contact surfaces of all cooking equipment shall be kept free of crusted grease deposits and other accumulated soil.

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not kept clean.

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”. (corrected on site)

Refrigerated storage. refrigeration facilities. each mechanically refrigerated facility storing time/temperature controlled for safety (tcs) food shall be provided with numerically scaled indicating thermometer, accurate to 3°f if scaled in fahrenheit only. . recording thermometers, accurate to 3°f if scaled in fahrenheit only, may be used in lieu of indicating thermometers. thermometers that are scaled in celsius or dually scaled in celsius and fahrenheit shall be designed to be easily readable and accurate to ±(1.05°c) in the intended range of use.

General. using shipping containers / milk / produce crates as storage racks / support shelves.

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

Cleaning frequency. food-contact surfaces of grills, griddles, and similar cooking devices and the cavities and door seals of microwave ovens not cleaned at least once a day; except that this shall not apply to hot oil cooking and hot oil filtering equipment if it is cleaned as specified in subsection (f) of this section. the food-contact surfaces of all cooking equipment shall be kept free of crusted grease deposits and other accumulated soil.

Storage. facilities for the storage of knives, forks, and spoons shall be designed and used to present the handle to the employee or consumer.

Toilet fixtures. easily cleanable receptacles not provided for waste materials.

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

Storage, separation of materials. poisonous or toxic materials not stored so they cannot contaminate food / equipment / utensils / linens / single-service and single-use articles. this may be accomplished by separating the poisonous / toxic material by spacing / partitioning and locating the poisonous / toxic material in an area that is not above food / equipment / utensils / linens / single-service or single-use articles. this item does not apply to equipment or utensil cleaners or sanitizers that are stored in utensil-washing areas for availability and convenience if the materials are stored to prevent contamination of food / equipment / utensils / linens / or single-service or single-use articles. (corrected on site)

Cleaning equipment storage. after use, mops not placed in a position that allows them to air-dry without soiling walls / equipment / supplies.

Sanitation poster not conspicuously posted in area accessible to all employees / not conforming to all requirements.

Inspections; reports. the person in charge failed to demonstrate knowledge. (corrected on site)

General. using shipping containers / milk / produce crates as storage racks / support shelves.

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

General. container of food not stored in the manner that protects food from splash and other contamination.

Hair restraint. while handling food or utensils, food employees not wearing effective hair restraints and clothing that covers body hair to prevent the contamination of food or food-contact surfaces. an effective hair restraint means any cap / hat / hair net made of fabric / cord / plastic / paper that effectively covers and holds hair in place. the use of effective hair restraints also applies to any exposed scalp or facial hair where there is the potential for contamination of food or food-contact surfaces. an effective hair restraint shall also be used in the partial or complete absence of scalp hair to preclude touching of the scalp and returning to food handling without hand-washing. facial hair restraints are not be required when facial hair is well-groomed and trimmed. (corrected on site)

Wiping cloths. moist cloths used for wiping food spills on kitchenware and food-contact surfaces of equipment not clean / not rinsed frequently in one of the sanitizing solutions permitted in section 20-21.12(e)(02) through (06) of this code / used for no other purpose. these cloths shall be stored in the sanitizing solution between uses.

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

Utility line/duct installation. exposed utility service lines and pipes not installed in a way that does not obstruct or prevent cleaning of the walls and ceilings. utility service lines and pipes shall not be unnecessarily exposed on walls or ceilings in those areas listed in subsection (b) of this section. service lines behind counters used only for beverage preparation may be exposed on the inside counter walls if necessary for service and if kept to a minimum. if exposed in rooms or areas allowed in subsection (c) of this section, air conditioning / ventilation / heating ducts shall be of smooth rigid metal and designed with a circular cross-section.

Storage, separation of materials. poisonous or toxic materials not stored so they cannot contaminate food / equipment / utensils / linens / single-service and single-use articles. this may be accomplished by separating the poisonous / toxic material by spacing / partitioning and locating the poisonous / toxic material in an area that is not above food / equipment / utensils / linens / single-service or single-use articles. this item does not apply to equipment or utensil cleaners or sanitizers that are stored in utensil-washing areas for availability and convenience if the materials are stored to prevent contamination of food / equipment / utensils / linens / or single-service or single-use articles.

Presence and use, restrictions, conditions of use. poisonous / toxic materials unnecessary for the operation / maintenance of the establishment / cleaning and sanitization of equipment and utensils / control of insects and rodents are prohibited in the food establishment; provided, this requirement does not apply to packaged poisonous / toxic materials that are for retail sale. restricted use pesticides specified in item (03)c of this subsection shall meet the requirements specified in 40 cfr 152, subpart i, classification of pesticides.

Cleaning equipment storage. after use, mops not placed in a position that allows them to air-dry without soiling walls / equipment / supplies.

Refrigerated storage. refrigeration facilities. each mechanically refrigerated facility storing time/temperature controlled for safety (tcs) food shall be provided with numerically scaled indicating thermometer, accurate to 3°f if scaled in fahrenheit only. . recording thermometers, accurate to 3°f if scaled in fahrenheit only, may be used in lieu of indicating thermometers. thermometers that are scaled in celsius or dually scaled in celsius and fahrenheit shall be designed to be easily readable and accurate to ±(1.05°c) in the intended range of use.

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”.

Temperature measuring device, food. food temperature measuring devices accurate to ±02°f in the intended range of use not provided / not used to assure attainment and maintenance of proper internal cooking, holding, or refrigeration temperatures of all time/temperature controlled for safety (tcs) food if the thermometers are scaled only in fahrenheit. if the thermometers are scaled in celsius or dually scaled, they shall be accurate to ±01°c in the intended range of use. a temperature measuring device with a suitable small-diameter probe that is designed to measure the temperature of thin masses not provided / not readily accessible to accurately measure the temperature in thin foods, such as meat patties and fish fillets.

General. contamination event. food establishment without written procedures for employees to follow when responding to vomiting or diarrheal events. (corrected on site)

Cleaning frequency. kitchenware and food-contact surfaces of equipment not washed, rinsed, and sanitized after each use and following any interruption of operations during which time contamination may have occurred. (corrected on site)

Using chemicals for sanitization. when using chemicals for sanitization, a test kit or other device that accurately measures the concentration of the solution in parts per million or milligrams per liter not provided and used.

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

Utility line/duct installation. exposed utility service lines and pipes not installed in a way that does not obstruct or prevent cleaning of the walls and ceilings. utility service lines and pipes shall not be unnecessarily exposed on walls or ceilings in those areas listed in subsection (b) of this section. service lines behind counters used only for beverage preparation may be exposed on the inside counter walls if necessary for service and if kept to a minimum. if exposed in rooms or areas allowed in subsection (c) of this section, air conditioning / ventilation / heating ducts shall be of smooth rigid metal and designed with a circular cross-section.